Welcome to Our Community

Unlock hidden features. Sign Up for Free Today!

ZANTRY CNC

Discussion in 'CNC Mills/Routers' started by Adam Filipowicz, Apr 30, 2017.

  1. Adam Filipowicz

    Adam Filipowicz Veteran
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    176
    Likes Received:
    42
    Adam Filipowicz published a new build:

    Read more about this build...
     
  2. Adam Filipowicz

    Adam Filipowicz Veteran
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    176
    Likes Received:
    42
    Looking forward to hearing some feedback on this idea.

    Current photo is a quick rough to get the idea out of my head
    doesnt include wheels and many other small parts.

    once I flesh this out I will redo a proper cad drawing.

    I like that so far this is all Openbuilds parts. No custom Plates

    What I dont like is 5 Steppers
    C-Beam Linear Actuator 250mm v1 XL v4.jpg
     
    #2 Adam Filipowicz, Apr 30, 2017
    Last edited: Apr 30, 2017
  3. Julius

    Julius Veteran
    Builder

    Joined:
    Nov 13, 2015
    Messages:
    159
    Likes Received:
    46
    No need for all those corner brackets. Just bolt into T nuts through the plate that then connects to the threaded rod.
     
    Mark Carew likes this.
  4. Rick 2.0

    Rick 2.0 OpenBuilds Team
    Staff Member Moderator Builder

    Joined:
    Dec 20, 2013
    Messages:
    1,293
    Likes Received:
    519
    You might consider moving the X-axis to the back side of the vertical risers. This will center the mass of the router better over the Y-axis wheels.
     
    Mark Carew likes this.
  5. GrayUK

    GrayUK Master
    Staff Member Moderator Builder

    Joined:
    May 5, 2014
    Messages:
    975
    Likes Received:
    247
    As Rick said, with the spindle/router out on a limb like that, you are putting a lot of stress onto the wrong side of the gantry.
    Gray
     
  6. Adam Filipowicz

    Adam Filipowicz Veteran
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    176
    Likes Received:
    42
    Thanks for the feedback!
    here is an updated version

    Zantry-CNC-May-v1-v6.jpg
     
  7. Rick 2.0

    Rick 2.0 OpenBuilds Team
    Staff Member Moderator Builder

    Joined:
    Dec 20, 2013
    Messages:
    1,293
    Likes Received:
    519
    Looks good. :thumbsup:

    If you're dropping back to single gantry plates on the Z-axis (which should more than sufficient), you might consider using the C-Beam™ Gantry Plate - Double Wide plates instead, connecting the X beam to the upper half of the plates (leaving the lower half operating in what is functionally dead space along the sides of the Y axis). This will give you another 45mm to work with in both the X and Z directions and make the frame a bit stiffer due to the increased vertical spread of the wheels. I would also suggest the 8 wheel configuration on these plates for additional rigidity.

    Rick.
     
    MaryD likes this.
  8. Adam Filipowicz

    Adam Filipowicz Veteran
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    176
    Likes Received:
    42
    XL gantry plate can do 6 outer and 4 inner mini wheels correct?

    Double gantry 8 mini inner

    I would have though XL would be stiffer.
     
  9. Rick 2.0

    Rick 2.0 OpenBuilds Team
    Staff Member Moderator Builder

    Joined:
    Dec 20, 2013
    Messages:
    1,293
    Likes Received:
    519
    No, the XL plate doesn't accept inner wheels. So the difference here is the leverage provided by the roughly 145mm vertical spread of the double gantry wheels versus the 100mm vertical spread of the wheels on the XL plate. This will help with both the racking of the frame and resisting the torsional load induced on the X axis by the spindle. (It doesn't help the X axis itself, merely the way the force is transmitted into the Z axis.)
     
    Adam Filipowicz likes this.
  10. Adam Filipowicz

    Adam Filipowicz Veteran
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    176
    Likes Received:
    42
    Good to know! Thanks!
     
  11. Adam Filipowicz

    Adam Filipowicz Veteran
    Builder

    Joined:
    Dec 21, 2014
    Messages:
    176
    Likes Received:
    42
    Revised again switched to Double Wide Gantry plates for Z and Y

    again,. please ignore some of the obvious errors in the rendering. (, random wheels, screws, acme being too short lol) :)

    Zantry CNC May v1 v7 Under.jpg Zantry CNC May v1 v7 Back.jpg Zantry CNC May v1 v7 front.jpg
     
  12. Kevon Ritter

    Kevon Ritter Veteran
    Builder

    Joined:
    Apr 30, 2015
    Messages:
    96
    Likes Received:
    32
    I was just thinking about something like this today too! Then I said no since it would be another axis that could become shifted.

    But your z travel is going to very poor if you used the bottom on the double c beam plate.
     
  13. Kevin Henning

    Kevin Henning Well-Known
    Builder

    Joined:
    Mar 18, 2016
    Messages:
    10
    Likes Received:
    1
    I like the idea of this... Julius, your suggestion of mounting the plate directly to the C-Beam using T-nuts (and then getting rid of the cast corners) is also something I had noticed... Do you know if the head of a low profile screw will fit in the gap between the plate and the C-Beam with the threaded rod, or would it be necessary to countersink the screws?

    Adam, if you don't want to run 5 steppers it may be possible to increase the height of the base and then have the Y and/or Z axes driven from underneath using the standoff plates and some GT-3 belt pulleys... It would work in wood, etc, in the same way as the Ox, but I don't know how well it would handle working in aluminum if that was a target material for you.
     

Share This Page

  • About Us

    The OpenBuilds Team is dedicated helping you to Dream it - Build it - Share it! Collaborate on our forums and be sure to visit the Part Store for all your Building needs!
  • Like us on Facebook

  • Support Open Source FairShare Program!

    OpenBuilds FairShare Give Back Program provide resources to Open Source projects, developers and schools around the world. Invest in your future by helping others develop theirs!

    Donate to FairShare!