Select a Category
Build Author Martin.Barfoed Views 44916
Large format 1200X1500mm OX Build using Stainless Steel plates, dual belt configuration. Limit switches is a mix of micro switches and NPN Proximity switches. Electronics based on parallel break out board, Long Motor Stepper drivers (Chinese stuff) and motors controlled by Mach3. Spindel will be Kress 1050.
Build Author Brian Popp Views 3811
Salmon Sphinx 1.0
A tribute build based on Kyo's wonderful CBeam Sphinx. My hope is to improve on that build slightly, but to be honest, I'll probably just screw it up. I'll use this build to publicly document my failures.
Build Author Savvas Views 3716
CNC Control Box with VFD etc etc
I'm currently working on the CNC control box, before doing any future work on the CNC Mountain Machine. I want the controller to be future proof and as professional as I can manage. I am planning to use stepper drivers, PSU's, a motor contactor unit to turn everything on, as well as a VFD and proximity limits switches. Each video will document the process and steps involved in researching, designing, planning and assembling a controller. I am not a natural electrician so learning as I go.
Build Author Rick Holder Views 937
Gantry Type CNC with Makita Router
The machine has met and exceeded my expectations on repeatability and accuracy. Cost was approx £600 including the Windows tablet.
Build Author Ryan James Views 1361
A smaller version of a standard D-bot. Smaller to fit better in my workable area and to fit my vision for the printer.
Build Author Anthony Bolgar Views 2779
CO2 Tube life expectancy experiment - Sponsored in part by Openbuilds
Hypothesis - Running CO2 laser tubes at high amperage may shoirten tube life in number of hours, but will be made up for by the increase in actual inches engraved/cut using the higher power. This is a long term experiment, so the build status will remain as "Build in progress" until the experiment has been completed.
Build Author Giuliano M Views 27487
H-Bot CoreXY Cube
Build Author Rob Altenburg Views 2632
Rob's D-Bot Build
The plan is to make this a fairly stock D-Bot build. We'll see if mods start creeping in.
Build Author Indieflow Views 52421
A lightweight, portable, accurate 3D Printer that has a good sized print area and small overall footprint that is easy to build, with easy to source components. The design is OpenSource allowing those with the capability to make their own parts get up and running.
Build Author Chefson Views 4528
OX CNC Router
Ca fait 2 ans que je rêve d'une Fraiseuse CNC. Ni trop grande ni trop petite, sans avoir le budget pour en acheter une toute faite. Je suis artisan menuisier ébéniste et j'ai finalement décidé de la construire. Le projet OX m'a séduit, alors je me lance.
Build Author Robert E. Nee Views 1563
Large cartesian gantry style 3D printer
This will be a fixed bed, v-slot implemented X,Y,Z axis gantry style 3D printer.
Build Author Giarc Views 17912
Lead Screw Driven Ox Derivative (850x1500)
Another build based on the original OX design with a cutting area will be about 26" (680mm) x 50" (1300mm) and driven by lead screws.
Build Author Glenn Weston Views 8596
"The Moagie Mill" My C-Beam XLarge
My Experiences building the C-Beam X Large. Maybe you can pick up a few pointers from my ramblings and experiences if you are considering building this machine.
Build Author kallibaba Views 4144
Two color Drawmachine
GRBL, vvvv, drawbot, penchanger, custom plates
Build Author dogmeatk Views 1616
Dogmeat's Custom C-Beam XL
I love the C-Beam XL concept, this build is my custom version with the goal of increasing rigidity for metal milling.
Build Author Greg Lampman Views 2665
C-Beam Intro to CNC
Build log for my first CNC machine, a C-Beam Plate Maker
Build Author recoush Views 1214
CoreXY 3D build one
an 8020 build with 1010 extrusion (1") Square tubing Rough size is 24x24x36 (600x600x900) The expected usable print area 21.5x21.5X32"roughly (510x510x760) An XY 3D printer with 3 extruders and 3 Z-axis 0.9 degree motors the table (Z-AXIS) will lift up to the XY Carriage on 3 12mm linear rod and 3 8mm Lead screw's Corexy designs complete and Z-axis build is started don’t have a 3D cad system yet so building my prototypes on a pcb layout tool
Build Author Gary Caruso Views 9615
OX Heavy Duty Build
OX Heavy Duty, using Chrisclub plates, for 2080 X-Y and C-beam Z
Build Author Shortyski13 Views 1352
A Large CoreXY build that can just barely get in through a doorway, aiming for under $1000. Build Volume approximately 18in x 24in x 26in.
Build Author Apothus Views 2570
Sphinx rigid XL
Rigid variant of the C-Beam sphinx platform
Build Author antonyking Views 4530
3D PrintBot 500x500x500
Large scale True 500x500x500 build volume 3D printer.
Build Author Giuliano M Views 2346
CoreXY cube with 600x600x800 volume.
Build Author WildBill Views 1491
C-Beam XL build
So for a summary its a great kit that was easy to build, could not be more happy.
Build Author 3D Meister Views 870
Camera slider with rotation prototype
I made a cam slider prototype with adjustable rotation to get experience for my CNC milled slider in planing.
Build Author evolver56k Views 1224
The Artist Formerly Known as Prints
Work in progress large volume CoreXY printer
Build Author McAdam Views 1156
Need a catchy name - enlarging CNC
The aim of this build is to have a CNC that can cut a FULL sheet of wood when I need it to, but also shrink down and cut smaller sheets the rest of the time. The prototype is based on an OX cnc but soon it will be completely custom using Openbuilds Parts
Build Author J-Wahl Dezign Views 2344
1.4 meter tall build height, 300x410mm build plate cartesian
The original plan was to build a 3d printer with a 1200x1200 build platform with a 600mm build height. I was having issues getting ahold of a large enough borosilicate glass plate for the build so I decided to go for build height. I plan on using a smoothieboard for the controller. The build has currently slowed down. I was removing a broken drillbit from the linear rail mount, and it shattered and took out my eye. I am doing what I can when I can focus my eyes long enough for the build.
Build Author Matt Barile Views 1307
Fixed Gantry Welded Steel Router
Fully welded, fixed gantry CNC router, with chinese linear motion parts, in progress
Build Author Robert Huxford Views 815
High Intensity Dive Light
Long duration , high intensity SCUBA dive light using Li-Po 18650 batteries and advanced circuitry.
Build Author Eric Kiser Views 3549
Live D-bot build at MRRF 2017 (Mar 25-26)
I will be attending the 2017 Midwest RepRap Festival (MRRF) with a small team of printer enthusiasts with a goal to fully assemble a Core-XY D-bot onsite during the event. This is our first attempt at building a D-bot and we will be learning things as we go. Our hope is to have the entire machine assembled, wired, and functional (at least to the setup and testing phase) before the end of the show. Please attend and watch us in person or visit our feed channel during/after the event.
Build Author Tom Dirriwachter Views 1093
3DS Cube 3 Modular Extruder
How to modularize the 3D Systems Cube 3 extruder nozzle.
Build Author lee Coughanour Views 1211
A work in progress
One of my first projects might be cutting proper plates.
Build Author Dmknerr Views 960
Server Rack Printer
My first project build. Concept build to use an existing 7.5 ft tall server rack as the frame. This ptoject may never be completed.
Build Author Garrettcompston Views 1857
My 2nd cnc build
My new build to upgrade from my worn out shapeoko
Build Author Lumberjack Engineering Views 4283
SOLAC: Space Optimized LAser Cutter
The Space Optimized LAser Cutter is a 40 watt CO2 laser cutter that supports a maximum part volume of 24" x 16" x 6.25". It consists of a V-slot frame + brackets/mounts designed to be 3D printed on a consumer desktop printer. Total cost of the machine is ~ $1,400 USD.
Build Author Anthony Bolgar Views 6047
L'FOX - Large Format OX deriviative. Designed and built by Revision 13 Prototypes
This build is for a testing rig to use while testing out different controller boards and CAM software for milling and routing. It is in the early stages, planning is complete, parts are ordered. Awaiting parts delivery to start build. Please not the BOM only covers parts from the OpenBuilds part store. I will be posting the other required items very shortly.
Build Author LarsTveito Views 2991
Ox Stainless with ballscrews
Ox Stainless with ballscrews for motion, nema 23 steppers, LInuxcnc for control software. Using basic parts for frame from Makersupplies, and the rest sourced from ebay. Building a small router hoping it will be able to cut aluminum with decent results.
Build Author seedorff Views 2143
This is my OX. There are many like it, but this one is mine. My OX is my best friend. It is my life. I must master it as I must master my life.....
Build Author Kevon Ritter Views 3865
Yet another Sphinx
Here's my Sphinx with a few slight modifications.
Build Author Mike Hake Views 949
Epoxy dispenser, to apply non-conductive epoxy to electronic board.
Epoxy dispenser, 2nd one, first one works great. Uses HMI to allow for operator to pull up files for different jobs. 9 prox sensors, Eot and home on all 3 axis. High quality nema23 motors with intergrated drives from applied motion. Uses programmable router for drives.
Build Author seedorff Views 928
A simple made hideaway for ugly electronics
Build Author HPB Views 10858
A simple XY laser engraver/cutter
A simple low-cost XY plane laser engraver/cutter inspired by the Much 4 laser build, with minimal parts and assembly time. Uses standard off the shelf components in almost 90% of the build with the exception of the axes motor and wheel mounts which need to be 3D printed.
Build Author Metalguru Views 6731
Big Ox Heavy Duty
A Heavy Duty version of the standard Big Ox build.
Build Author Michael Views 46142
CNC xPRO Driver
Spark Concepts CNC xPRO Driver. A new GRBL compatible, all-in-one stepper driver board with 4 motor controllers for XYZ + 1 clone (or rotary!). Capable of powering your next build with an ATX PSU (or 12V 2 wire supply), and ready for wireless printing. Compatible with Arduino (wireless robots anyone?)
Build Author techmod Views 3163
This is going to be a more or less detailed how to build BetterBot. Pictures and more (decent) text are to be added.
Build Author PhotoSgt85 Views 5258
C-Beam Machine XL
Overview of my experience building the C-Beam Machine XL from OpenBuilds, along with updates as I move along and get it going. My application is for creating plates needed for lab functions, 19 rack bay covers, and whatever else arises.
Build Author Michael Forte Views 817
OX CNC Build
OX CNC built using the kit from SMW3D with a Smoothieboard 5 and external motor drivers.
Build Author jamesdjadams Views 3567
C-Beam XL - TinyG - Aluminium Plate - Dewalt 611
C-Beam XL build using TinyG V8.
Build Author IndyMaker Views 4103
Ooznest Ox with 3D Printed Gantry Plates
Ooznest Ox with gantry plates and end caps 3D printed in ABS rather than aluminum.
Build Author Bernie CLark Views 2371
C-Beam XXLarge "Laser "Tank""
A re-imagining of Dollarz81's XXL Tank in Laser form
Build Author DazTheGas Views 12927
From where Mark left off from the Ox build I am going to film the whole process of customizing the Ox.
Build Author Hackscribble Views 15318
1000mm x 750mm OX with some planned enhancements. My first venture into CNC.
Build Author dodgenet Views 1622
Budget 1500mm OpenBuilds V-Slot Deltabot Build
This 1500mm tall Delta is a work in progress. The triangle corners are water jetted from 1" 6061 Aluminum, and are welded to 1" square tubing. The 1500mm OpenBuilds 20x20 V-Slot extrusions are held into the corner brackets by two stainless steel set screws per bracket. This printer will need to be reinforced with wall brackets due to the combination of height/materials.
Build Author BeTrue3D Views 5932
High Quality CoreXY with focus on quality and optimized printarea versus physical size of the printer.
Build Author adambrum Views 1739
Slightly larger sphinx
Another C-Beam Sphinx but a little larger,
Build Author Tom West Views 3160
Hlidskjalf, CoreXYU (dual X-carriage)
Dual X-Carriage CoreXY. Not impossible, but probably the only one. Use the link to Thingiverse "Hlidskjalf" for parts and downloads.
Build Author Ronald van Arkel Views 8401
Upgrading the C-Beam machine
So we have new plates, stronger motors, belt drive reduction, but what should we do with them? In this article you might find the answer you were looking for as we took an “old” C-Beam machine and started to upgrade the X/Z body and added more torque and precision to the Z-axis.
Build Author kylesmth Views 1441
Lead screw printer
High quality e3d parts with a minimalist design
Build Author Hytech2k Views 56216
Area 51 CNC Parts F-117 CNC Gear Rack Drive System
This is my journey on building a rack and pinion Ox variant called the F-117 CNC.
Build Author Dollarz81 Views 4468
C-Beam XXLarge "Tank"
This is a modified build C-Beam XLarge. 1000mm C-Beam used for X and Y axis, and the Y Axis moves the X bridge, not the material being worked.
Build Author ANDRESCAMPA Views 1610
SUPER OX NEMA 34 1600 OZ Motors!!!
CNC OX 1500X3000
Build Author Jonathon Harms Views 1360
Schematix Ox-Metal Build
A build of Schematix's Ox-Metal design, with a 0.8kw watercooled spindle.
Build Author Steven Sampson Views 5793
A CNC router designed to handle a 4'x8' sheet, for as close to $2000 as possible. The price barrier resulted in my choice to use timing belts rather than leadscrews or rack&pinion. Build List still being updated
Build Author mikethebomber Views 4275
A humble first time attempt at building a 3d printer from scratch
Build Author peter28 Views 1573
i wanted to use both the ox and the C beam C beam for the gantry because its stronger i also made the gantry 20 mm higher so i can cut thinker material i will maybe later go to rack& pinion on the 1500 mm Y axes also instead of the V wheels i will maybe go to hiwin in the furture
Build Author Martin Skov Nielsen Views 2498
Stainless OX kit
This is a 1500 X 1500 Stainless OX kit build, by a cnc novice. It is the first cnc machine i have ovned and build I got this kit from http://makersupplies.dk/20-ox-cnc-kits
Build Author SBLabs Views 5517
C-Beam to C-Beam XL Upgrade
This is my first public build. Please be kind. We upgraded our C-Beam to the C-Cbeam X-Large. I want to give special thanks to Moag and the OpenBuilds team for making this happen.
Build Author James Hayes Views 2452
Pure Cbeam 900x1000
This is a pure cbeam build to maximize envelope and rigidity. All the parts used are available from open builds.
Build Author Schematix Views 55057
OX-Metal CNC Router Mill
The OX-Metal is based on the original OX CNC mill But with a few modifications and add-ons
Build Author Power Playground Views 1347
This is my own modified version of the D-Bot printer. I wanted to spec this printer to be able to print exotic materials at high accuracy with little to no compromises and maximum reliability.
Build Author Edgar Robles Views 1269
Sheethexapod works with basic mechanims as direct metal-metal links and joints, all movements can be done by a rc servomotor in this case towerpro model.
Build Author Jen Views 3831
My first OX build
This is the story of my experience building a 1000 x 750mm OOZNest OX CNC router
Build Author Aleksandar Views 5085
Currently I have Velleman/3Drag K8200 modified and CNC machine self built and wanted to use both to make new 3D printer. After looking at different designs I liked Voron a lot and have decided to go that way. Currently I have ordered majority of parts and build shall start soon. I don't plan to rush it as I am usually 2 months home and 2 off.
Build Author Silverrabbit2 Views 3445
Ooznest OX, Workbench, & Folding Table
An OX based unit with innovation surrounding it -- 9 drawers, workbench, folding CNC table, & portability.
Build Author anigeek65 Views 11150
OX Super "C" - Cpmpleted 11/02/16
This CNC utilizes the C-BEAM extruded aluminum for the "X", "Y", and "Z" axis. The gantry will move similar to the OX along with the "Z" except I am incorporating the C-BEAM instead of the 20x60 V-RAIL. To make the system as strong as possible I am using two C-BEAM rails back to back. The "Y" axis will encompass two sets of roller on both side of the C-BEAM extruded rails for added strength. All of the plates for this were created using the C-BEAM machine I completed several month ago.
Build Author sebf34 Views 11732
OX Based cnc 3000 x 1500 Double belt
OX Based CNC
Build Author Jonathon Duerig Views 3937
CNC Glass Grinder
This is a 1-Axis CNC Glass Grinder. It uses a hobby grinder to miter a precise angle on the edge of a piece of glass.
Build Author Moag Views 32290
C-Beam Machine XLarge
A rigid and wide format, plate and carving CNC.
Build Author Sonny Lowe Views 2953
MakerSL MSL-8 OB Vise
Small Machining Vise designed around 20x80 Openbuilds Rail System
Build Author MikeBardsley Views 3425
Fast, Large build area, CoreXY design
Build Author Iwan Müller Views 2039
Controlbox for a CNC Router
A Controlbox for my CNC-Router, containing stepper-drivers, Planet-CNC MK3 Controller and a Controlpanel with joysticks.
Build Author P. ry Views 8272
Nox 1500mm x 1500mm C-Beam
C-Beam build using a double C-Beam for the X axis. 1500mm x 1500mm
Build Author Krishnakumar Views 2526
Hobby OX CNC
This "hobby OX" CNC is built for multiple purposes such as cutting and engraving various materials, laser etching and cutting, etc... Its a great platform for hobby enthusiasts like me where this machine can be used for so many different purposes effectively and efficiently!
Build Author MattiasN Views 15945
MyCNC(1000mm x 1500mm)
My CNC project
Build Author uran Views 4345
TesseractXY (MendelMax 1.5 version)
History about making 3d printer.
Build Author Joe 90 Views 3817
Schematix OX metal build
OX metal build from an noob
Build Author Martin Bogomolni Views 5269
Delta-Six ( Jerry426 variant )
Building a Delta-6 variant, using recycled parts from a WolfStock Delta printer.
Build Author slm222 Views 1280
Cheap linear rail set up for z-axis
A easy to do cheap upgrade for the z axis
Build Author Asaku Views 3654
Hi! This build is, or at least should be, a multipurpose box (mBOX). Due to limited space I want to build something that can serve multiple purposes such as 3d printing, 3d scan, plexiglass cutting and hopefully some milling too (both wood and metal). Switching between modes should involve switching heads and worksurface (change heatbed with a wood platform and viceversa). (for the scan part I'm thinking of integrating this opensource project into the frame: http://www.freelss.org/ )
Build Author mytechno3d Views 8385
Plasma cutting table
This is our plasma cutting table , based on the famous OX CNC . Can cut up to 15 mm ( steel , stainless , aluminium ) with a really good accuracy and at a really high speed .
Build Author semperfikurt Views 11548
Beefed-up and customized OX build
My Machine is based on the OX CNC designed by Mark Carew as well as the ooznest kit, and it incorporates a bunch of my own details and revisions to increase performance and robustness. It has become way more beastly than I originally planned!
Build Author Dave420 Views 4345
10 x 5 ft plazma table build
Attaching V Slot or mutable V Slot end on end to a larger steel frame table.
Build Author David the swarfer Views 7958
The Nguni - an OX variant
A modified OX with more X clearance, MDF plates, vacuum table
Build Author Metalguru Views 2536
Custom black and red Big Ox
Build Author Rakmup Views 21067
CNC Router Lathe
Steel square tube frame with dual feed gantry and indexing lathe section. Will have 36" x 30" x 6" travel.
Build Author sergeysapiro78 Views 1610
Zen3D Atlantis 3D printer, H-Bot mechanics
H-Bot mechanics 3D printer. Build volume - 300x300x300mm dimensions: 560x500x500mm
Build Author nate campbell Views 2531
CrOX Carbon Reinforced OX
Modified OX with carbon fiber reinforced X and Z axes. 1500mm Y, 1000mm X and 120mm Z clearence
Build Author Dexter Oddwick Views 2017
Black Rabbit 1500
This is a router that I designed that is loosely based on the Openbuilds Ox, but designed to be heavy duty, rigid, and yet quick and agile.
Build Author Bon Thomassen Views 5210
D-Bot CoreXY printer
A CoreXY D-Bot 3d printer using gantries as wheel-carriages.
Build Author Erick Sauvé Views 2903
My first build: a other OX CNC
I love to build things. I decided to build a CNC machine to help me build more things! I had a lot of fun and I learn a lot of thing in the process of building this machine. p.s. my primary language is french not english. Forgive me if I made some mistake.